In This Article:
- Starlink home screen
- First person view (FPV)
- Flight control settings
- Remote controller settings
- Wi-Fi settings
- Aircraft battery settings
- Gimbal settings
- General settings
- Camera settings
- Video settings
Home screen
Button | Description |
---|---|
Return to the home page | |
View and edit the photos and videos that you have downloaded | |
Autel Online Store (under development) |
|
Register or log into your account | |
Status of the camera connection | |
Your aircraft model | |
Start First Person View (FPV) |
First person view (FPV)
Button or Graphic | Description |
---|---|
Settings Access flight control, remote controller, video link, aircraft battery, gimbal, and general settings |
|
![]() |
Remote Controller Signal Displays the strength of the remote controller signal Tap to open the remote controller settings |
![]() |
Video Link Signal Displays the signal strength of the Wi-Fi Video Link (X-Star) or HD video streaming (X-Star Premium) between the aircraft and the remote controller Tap to open the video link settings |
![]() |
Advanced Camera Settings Access photo settings, video settings, and camera settings |
Camera Settings Choose automatic or manual settings for ISO, shutter speed, and EV |
|
Record video Tap to start or stop recording as well as access video settings | |
![]() |
Take a photo Tap to take a photo or access photo settings Select a shooting mode (Single Shot, Burst Shooting, AEB, or Time Lapse) from photo settings This button will change in appearance depending on your shooting mode selections |
Pitch Control Control the camera pitch movement Displays the camera pitch angle indicator in the upper right corner |
|
Map Split Screen Displays map in bottom left corner Tap to switch to the map view in FPV |
|
Distance Horizontal distance between the aircraft and the home point | |
Altitude Altitude of the aircraft relative to the home point level | |
Flight Speed Current flying speed of the aircraft | |
![]() |
Flight Status
Arrow indicates the tilt angle of the aircraft’s nose
Colored ring indicates the current battery level of the aircraft:
- Green bar is present when there is abundant battery - Yellow bar indicates Low Battery and you should let your aircraft Go Home - Red bar means Critical Low Battery and the aircraft will land onsite |
Remaining Flight Time The remaining time aircraft can be flown based on battery level | |
Battery Level The current battery level of the aircraft | |
![]() |
Starpoint Positioning System The distance between the surface and the Starpoint Positioning System sensors This button is highlighted only when the Starpoint Positioning System is in a working state |
Flight control settings
Button | Description |
---|---|
Compass Calibration | Initialize a Compass Calibration. |
Beginner Mode | Enable or disable Beginner Mode. This mode has a fixed maximum flight altitude (30 meters), distance (100 meters), and speed (horizontal: 6 meters/s, ascent: 3 meters/s, descent: 1 meters/s). These limitations help to keep your flight safe when you are learning how to fly. |
Flight Speed | Set limits for the aircraft’s ascent, descent, and horizontal speed when Beginner Mode is disabled. |
Altitude and Distance Limit | Set a maximum altitude and a maximum distance for your flight when Beginner Mode is disabled to protect the aircraft from losing the signal or flying out of sight. When these limits are enabled, the aircraft cannot fly outside the preset boundaries under GPS mode. In non-GPS mode, the aircraft is only restricted to the preset altitude limit. The distance limit in non-GPS mode may vary depending on the regulations and laws in different areas and countries. In GPS mode, the maximum altitude is set to 120 meters and the maximum distance is set to 800 meters by default. |
Go Home Altitude | Set a safe altitude for your aircraft to Go Home automatically in case of an emergency. When you set the Go Home altitude, the aircraft will adjust to the value you selected before returning to the home point. The default Go Home altitude is 30 meters. |
Advanced Settings | |
---|---|
Button | Description |
Enable ATTI Mode | Activate ATTI mode using the switch on the remote controller This mode is disabled by default to prevent accidental disabling of GPS mode. |
Front LED Indicator Lights | Toggle the two red LED indicators at the front of the aircraft on or off These LEDs help you to identify the aircraft’s nose direction during flight. |
Starpoint Positioning System | Enable or disable the Starpoint Positioning System |
Flight Data Recorder | Tap Format to clear all of your flight data |
Remote controller settings
The Remote Controller Settings screen gives you access to these settings: Gimbal Pitch Dial Sensitivity, RC Binding, RC Calibration, Command Stick Mode, and RC Language Setting.
TIP: You can also access this screen by tapping on the General Information Bar.
Button |
Description |
---|---|
Gimbal Pitch Dial Sensitivity | Adjust the sensitivity of the Gimbal Pitch Dial on the remote controller |
RC Binding | Pair the remote controller and aircraft When you replace any devices (e.g., aircraft, gimbal, or remote controller), you must rebind the remote controller and the aircraft by holding the RC Binding Button on the aircraft and this Bind button consecutively. |
RC Calibration |
Calibrate the remote controller's Left Command Stick, Right Command Stick, and Gimbal Pitch Dial You only need to calibrate your remote controller when using it for the first time or after your remote controller has been replaced. |
Command Stick Mode |
Choose which command stick mode (Mode 1, 2, or 3) you prefer to control the aircraft
|
RC Language Setting | Choose your preferred language for use on the LCD Flight Information Panel |
Wi-Fi settings
- You can rename the Wi-Fi SSID and reset the password on this screen
- Do not use spaces in the SSID or Wi-Fi password
Aircraft battery settings
- You can also enter this section by tapping
on the Aircraft Status Bar. This function allows you to view the current battery level and other information. Low Battery Warning and Critical Low Battery Warning settings are also available on this screen.
- For your safety, the Low Battery Warning cannot be set below 25% which is the minimum battery level for Go Home. Also, the Critical Low Battery warning cannot be set below 12.5% which is the minimum battery level for landing.
Gimbal settings
Button | Description |
---|---|
Gimbal Mode | Choose a working mode for your gimbal:
- FPV Mode synchronizes the camera gimbal movements with the aircraft to provide a real-time video piloting experience from a first-person view - Stabilized Mode enables stabilized camera tilting control for creative aerial photography |
Gimbal Calibration | Gimbal calibration helps to keep the gimbal level and steady for smooth photographing and filming. Before tapping, make sure your aircraft is level and nothing is obstructing the gimbal’s range of motion. Tap Calibrate to start an automatic calibration of the gimbal. |
Adjust Gimbal Roll | You can adjust the gimbal roll slightly while watching the camera view to find the best angle for your photography. |
Default Gimbal Angle |
The gimbal angle is set to 0° by default. You can set the gimbal angle between 0° and 90°. Use this shortcut to change the gimbal tilt angle:
|
General settings
Button | Description |
---|---|
Parameter Units | Choose Imperial or Metric as your preferred unit system |
Voice Prompt | Enable or disable the voice prompt |
Tutorial | Display or hide tips that appear before your operation |
Map | |
---|---|
Button | Description |
Show Flight Route | Display or hide your flight route on the map |
Calibrate Coordinates (For Mainland China) | Enable or disable the map calibration |
Background Caching | Enable or disable map caching in the background |
Clear Flight Route | Clear your flight route on the map |
Firmware Version | Display the firmware version of different components |
About | Display the version of the Starlink App |
Camera settings
Button | Description |
---|---|
Mode |
Choose between single shot, burst mode, or time lapse |
Size | Change the picture ratio to 4:3 or 16:9 |
Format | Choose between JPG, DNG, or JPG+DNG |
Style | Shoot photos in landscape, soft, or custom |
WB | Set the white balance to auto, sunny, cloudy, incandescent, neon, or custom |
Color | Change photo colors to vivid, black and white, art, film, beach, dream, classic, or nostalgia |
Video settings
Button | Description |
---|---|
Resolution |
Choose 4K/30fps, 1080p/120fps, or 720p/240fps |
Standard | Choose NTSC or PAL |
Format | Choose MOV or MP4 |
Style | Shoot films in standard, landscape, or soft modes |
WB | Set the white balance to sunny, cloudy, incandescent, neon, or custom |
Color |
Change the video color to vivid, B&W, art, film, beach, dream, classic, and nostalgia |